Skip to Content

Final Screen-4

Hi guys, it's week 3 of the One Room Challenge, and we're finishing up the AC/utilities corner part of the yard. Wahoo! Last week, I shared progress on the platform deck and some light rock landscaping. This week, I'm sharing the DIY AC unit screen I made. I'm going to share how I did it, but I'm not going to share a complete tutorial. It's unlikely that anyone (except my next door neighbor) has exactly the same layout and needs as we do. Here's what we used to make a DIY AC unit screen: (Affiliate links below. Thank you for your support!) 2x4s for the standing pieces 1x4s for the slats Random orbit sander Fine-frit sandpaper to polish by hand Saw, finish nailer Liquid Nails Heavy Duty Construction Adhesive Varathane wood stain in Kona Minwax Helmsman Spar Urethane in Satin Kreg Jig and 2.5" pocket hole screws And here's how we did it. (Remember to wear a mask and eye protection while sanding and working with wood, and wear an appropriate mask while working with stains and finishes. Follow the directions and warnings from your particular brand. Do not use any tools without proper training, precautions, and supervision. Read my full disclaimer here.) Step 1: First we measured how big we wanted the screen to be. We decided to shape it like an L and have it come up high enough to cover other utilities, not just the AC unit. (If you make a project like this, make sure it does not interfere with anything that requires air circulation or regular reading.) After deciding on measurements, and knowing we wanted each screen slat to be 1 inch apart, we calculated how much 1x4 we'd need. Once we had the final height (14 pieces of 1x4, each an inch apart), we cut the four pieces of 2x4 to height. (Yes, that's a diaper and a package of wipes in my purse. Times have changed.) Step 2: Next I gave each piece a quick sand using my random orbit sander. This was mostly to polish each piece up and break down any rough or splintery edges. After each piece was cleaned up, I wiped the whole lot down and stained each using the Varathane wood stain in Kona. I also drilled pocket holes in one of my 2x4s to create the main corner support (but didn't attach them yet). This, coupled with the next step, was by far the most time consuming. (But was faster using a small roller instead of a paint brush!) I was VERY GLAD at this point that I hadn't used 1x2 like I'd originally wanted. That would have been painful. Step 3: Once I had stained everything and it had dried according to my instructions, I gave each piece a few coats of the Minwax Helmsman Spar Urethane in Satin. Oof, talk about a slow process. (See my post on how to stain and finish wood here.) And one that took over my garage for several days. Luckily the urethane dries in about 4 hours, so that helped me get two coats in on one day. Everything is dry...time to assemble. Yay! Step 4: We began working on the longer side of our L-shaped screen first. Board by board, we spaced and nailed using a finish nailer. (By we, I mean my dad, who came over with his finish nailer to help me complete this project. Ramona was up, so I held her while she watched from inside. She loves grandpappy.) We did a 3/4" overhang on the left side. You'll see why. Step 5: Once the longer side was done, we did the shorter side. For those, we did a 1.5" overhang on the right side. Step 6: We stood the screen up to make sure everything looked right. Now here's where the pocket holes came in handy. We attached each side to one another by driving 2.5" pocket hole screws through the pocket holes. Since we also built an overhang in on each side, the sides fit together perfectly. And here it is in place! It fits perfectly over the L shape of pavers we laid and is perfectly level. I am super pleased with how this one turned out. It may have been time consuming, but it was worth it! And it matches the outdoor table and benches I'll be sharing soon. PIC You can also see I decided to dress it up a bit with some Pot Clips and pots we had in the garage. I love these things. Like this? PIN IT!

Leave a comment

Your email address will not be published. Required fields are marked *


    Comment spam is the worst. And it's why I had to turn off comments on my posts that are older than a few weeks. If you see a spot to leave a comment, please do. If you don't, I still want to know if you have a question! You can hop over to my Instagram and leave a comment or send me a direct message. Thank you for visiting and reading!
    +++
    This blog's content is for entertainment purposes only and is not professional advice. By reading this blog and attempting to re-create any content shared on it, you assume all responsibility. Read my full Terms of Use here. Be safe out there!